When a door rubs at the top, look first at the top corner on the latch side, the corner farthest from the hinges. A door hangs from its hinges like a gate, and when anything lets it drop or twist, the free corner moves the most. So before anyone reaches for a plane, find out why the door moved: trimming a door that is still moving only buys a few months.
Cause one: a sagging hinge
The top hinge carries most of the door's weight, pulling it away from the frame every time the door swings. Over years the screws that hold that hinge to the jamb loosen, or their holes strip out in the soft wood, and the top of the door tips toward the latch side. The gap along the top edge opens on the latch side and closes on the hinge side, the upper latch edge presses into the jamb, and the corner starts to drag.
To check, open the door halfway, hold the knob and lift gently. If the top hinge shifts or the screws creak, the hinge is loose; a screw that turns without tightening has a stripped hole.
Fixing a sagging door hinge
- Tighten what is loose. Snugging up screws that have backed out, without over-driving them, can pull the door back into line on its own.
- Fill a stripped hole. A screw spinning in a worn hole will not hold however hard it is turned. The hole is filled with glued wood, trimmed flush, and redrilled, so the screw has fresh wood to bite.
- Reach the framing. A longer screw in the top hinge, driven through the jamb into the framing behind it, pulls the hinge side tighter and lifts the latch corner when the frame itself is sound.
Then open and close the door several times. If the top corner clears and the latch catches without a push, the job is done, and nothing had to be cut.
Cause two: a door sticking in summer
If the door was fine in January and binds in June, the hinge may not be the problem. Wood swells as it takes on moisture from humid air and shrinks as the air dries. Atlanta summers are long and humid, so wood doors and frames are at their largest from late spring into early fall, and an exterior door, or one between an air-conditioned room and a garage, sees the biggest swing.
A door that sticks only in summer is still worth fixing, but gently. Planing it to fit on the most humid day can leave a wide gap and a draft in winter. Correct anything loose first, remove only as much wood as the door needs, then seal the cut edge so it does not swell back.
Door sticks at the top, the side or the bottom: what each one means
- At the top, on the latch side. The door has dropped toward the latch: the top hinge first, as above.
- Along the latch edge from top to bottom. The whole door has swollen, or paint has built up on the edge and the jamb.
- At the bottom, on the floor or the rug. New flooring or a thicker rug can be the cause rather than the door.
- At the top, on the hinge side. Here the door has tipped the other way: the top hinge sits too deep in the frame, or the bottom one stands too far out. Shimming or resetting that hinge fixes it; cutting the door does not.
Running a sheet of paper around the closed door finds the spot: where the paper catches, the door is touching the frame. Pencil marks on the edge, or a strip of light along the opposite edge, tell the same story.
When a sticking door is a sign of something bigger
A sticking door can be a hinge or the weather, or it can be telling you about the house. These signs point past the door:
- Several doors started sticking at once. One door is a door problem. Three or four on the same side of the house is a pattern.
- New cracks near the frame. Diagonal cracks running up from the corners of a door opening, or a crack that keeps getting longer, can mean the framing around the door is moving.
- Floors that have started to slope. A marble that now rolls toward one wall, or a gap opening under a baseboard, belongs with the cracks above.
That is structural work, and not something Tool Box Pros takes on. Planing a door to fit a frame that is still moving hides the symptom. Have the house looked at by a structural engineer or a foundation specialist first; once the movement is dealt with, adjusting the doors is the easy part.
What a handyman visit for a sticking door looks like
We start with the checks above: hinges, screws, the gaps around the door, and whether the binding is new or seasonal. Loose hinges are tightened or reset, stripped holes filled, a longer screw driven where it helps, and the strike plate moved if the latch no longer lines up. Only if the door still rubs do we plane the edge, and then we seal it. The estimate is free, and the price is agreed before we start.